Show notes
Blog: here. You can just imagine the movie trailer … "Your worst enemy has taken over all your flights, and you cannot remove them from your network. They demand a $1 billion ransom, or else they will bring every flight down. Bob accidentally removes one of the controllers — you now only have 25 minutes to save the lives of those in the air!" We have all seen movies with a dead man switch — and where an elaborate mechanism is created for someone to be killed if a random is not paid. But, anyone who tampers with the mechanism will cause the dead man switch to activate and kill the target. Now, this approach is coming to attacks on CNI (Critical National Infrastructure) and industry control systems (ICS). We have generally been fortunate that PLC (Programmable Logic Control) systems have been largely untouched by cyberattacks. But that is no reason to not focus on their security. Significant risks exist, especially for attacks against CNI — as highlighted with Stuxnet. In a new paper, Richard Derbyshire and a research team at Orange Cyberdefence [here] and Lancaster University focus on the scenario where an entire environment is controlled by an adversary and where all of the assets poll each other to make sure they remain untampered. Any changes to the configuration or a removal of any of the controllers will cause the system to go "Full ON" — and is similar to a Dead Man's switch [1][here] The paper outlines the increase in cyber extortion (Cy-X) tactics and where a key focus now is typically to both encrypt the target's data and exfiltrate their data. In most cases, this type of approach can be defended against in a PLC environment — by replacing existing hardware or resetting the configuration of devices (which is equivalent to a restore from backup). DM-PLC showcases a methodology which will overcome these recovery methods. CrashOverRide and Titon In 2016, the CrashOverRide malware was installed on the Ukrainian critical infrastructure, and which resulted in a cyber attack on the power supply network. It happened on an electrical transmission station near the city of Kiev (Ukrenergo), in December 2016 and resulted in a black-out for around 20% of the Ukraine population. Luckily, it only lasted for one hour, but many think that it was just a test — a dry run — for a more sustained attack. This attack has now been traced to the Crash Override (or Industroyer) malware. A previous attack on the Ukranian power infrastructure in 2015 involved the manual switch off of power to substations, but the newly discovered malware learns the topology of the supply network — by communicating with control equipment within the substations — and automatically shutdown systems. The company who analysed it (Dragos) thinks that it could bring down parts of the energy grid, but not the whole of it, and that the activation date of the malware sample was 17 December 2016. They also defined that the malware can be detected by looking for abnormal network traffic, such as looking for substation locations and probing for electrical switch breakers. Many suspect it may have been sent through phishing emails (as with the 2015 attack), and where Crash Override infected Microsoft Windows machines within the target network and then mapped out control systems in order to locate the key supply points, along with recording network activity which can be sent back to the controllers of the malware. After the discovery phase, it is thought that Crash Override can load up one of four additional modules, and which can communicate with different types of equipment (such as for Honeywell and Siemens systems). This could allow it to target other electrical supply networks within different countries. In 2018, too, it was reported that the Triton malware brought down safety systems for an oil and gas network in the Middle East [here]. This was achieved by the reverse engineering of the firmware used by device controllers and focused itself on specific parts of the infrastructure. A typical attack can often involve disabling safety systems — and which will protect the infrastructure on a system overload. When an overload does occur, the safety systems do not then protect the equipment, and this can lead to severe physical damage of the infrastructure. A tripping of just one part of the safety system, too, can cause a chain reaction, and bring down a large part of the infrastructure. DM-PLC With DM-PLC, all of the PLCs and engineering workstations (EWs) constantly poll each other and detect any deviations from the required attack behaviour — and thus disallow any changes to the overall running of the adversories objectives. If the system is tampered with, it activates a Dead Man's switch, and where the PLCs set their outputs to "ON". This could have a devastating effect on the physical infrastructure that the PLCs connect to. This — the research team say — moves away from the traditional ransomware approach of encrypting data within the infrastructure to one that allows the system to continue, but under the adversary's command. Figure 1 outlines the basic setup and where the team set up a number of objectives [1]: Deployable with minimal prerequisites from an EW. Runs in parallel to existing operational code. Does not impact existing operational code. Is resilient to tampering/response and recovery processes. Includes tamper detection. Can enact undesirable wide-spread operational impact. Requires a key to relinquish control back to system owners. Can be tested prior to being armed. Figure 1 [1] The main focus of the work is to define a framework for a DM-PLC, and then define mitigation techniques. In order to keep the deadlock, the devices then monitor each other for changes (Figure 2), and where alerts are raised for any perceived changes. Figure 2: Polling of devices Overall, the team successfully tested three main operations [1]: A PLC being removed from the network. The DM-PLC ransom timer expiring. The victim entering a code having 'paid' their ransom. In a scenario with three PLCs, Figure 3 shows the response to PLC 3 being removed from the network and where PLC 1 and PLC 2 set their outputs to 1 after 25 seconds — which causes the Dead Man switch to activate. Thus, someone taking PLC 3 off the network has 25 seconds before the whole of the network goes into "full ON" mode. Conclusions Dead Man PLC sounds like a script for a movie, but it is a movie that could play for real. Our CNI is precious, and we need to protect it. Otherwise, here's another movie … "Your worst enemy has taken over all the fun rides, and you cannot remove them from your network. They demand a $1 billion ransom, or every ride will stop instantly. Bob accidentally removes one of the controllers — you now have 25 minutes to save lives!" References [1] Derbyshire, R., Green, B., van der Walt, C., & Hutchison, D. (2023). Dead Man's PLC: Towards Viable Cyber Extortion for Operational Technology. arXiv preprint arXiv:2307.09549.